AIR FITTINGS AND ACCESSORIES
BLOW GUNS, COILED AIR HOSE, SWIVELS, TIRE INFLATORS

Safety Blow Gun

Basic safety blow gun for general purpose use. Tip pressure will not exceed 30 PSI, yet gives a good blast of air for cleaning. Safety glasses or shield must be worn when using any blow gun.
  • Large vinyl thumb grip provides additional user comfort.
  • Can now be used for water.
  • The area at the bottom of the blow gun is recessed to perfectly fit the user's fingers, allowing a firm, yet relaxed grip.
Safety Blow Gun
Part #Description
D204-301/4" Female NPT Inlet
NOTE: The Air Chief Blow Gun has a safety tip which prevents buildup of tip pressure in the event the outlet is obstructed or "dead ended". It complies with the requirements for OSHA 1910.242 (B) and 1910.95 when used on air lines of 150 PSI of less.


Premium Safety Blow Gun

The Premium Safety Blow Gun features a tough zinc die cast body that is made to last in even the harshest environment.
  • Flat black powder coat finish and nickel plated tip.
  • Superior corrosion resistance.
  • Ergonomic design of the body and large operating lever reduce user fatigue and discomfort, even during long term use.
Premium Safety Blow Gun
Part #Description
D204-30P1/4" Female NPT Inlet
NOTE: The Air Chief Blow Gun has a safety tip which prevents buildup of tip pressure in the event the outlet is obstructed or "dead ended". It complies with the requirements for OSHA 1910.242 (B) and 1910.95 when used on air lines of 150 PSI of less.


Safety Air Booster Blow Gun

The Safety Air Booster Blow Gun features multiple venturi holes that maximize air volume while conforming to OSHA standards
  • Noncorrosive heavy wall, yet lightweight construction assures long life in rugged industrial environments while easing user fatigue.
  • All brass internal components assure rust free operation.
  • Ergonomic design of the body and large operating lever reduce user fatigue and discomfort, even during long term use.
Safety Air Booster Blow Gun
Part #Description
D204-30SB1/4" Female NPT Inlet
NOTE: The Air Chief Blow Gun has a safety tip which prevents buildup of tip pressure in the event the outlet is obstructed or "dead ended". It complies with the requirements for OSHA 1910.242 (B) and 1910.95 when used on air lines of 150 PSI of less.


Brass Tip Blow Gun

Rubber Tipped Blow Gun

Brass Tip Blow GunRubber Tipped Blow Gun
Ventless tip provides the most economical means of achieving a concentrated air stream for many blow-off applications.Provides leakproof seal between gun and fluid line or other opening. Also excellent for cleaning molds or delicate surfaces where a metal tip might scratch or otherwise harm critical areas.
1/4" Female NPT Inlet1/4" Female NPT Inlet
Part #Description
D6051/4" FNPT
Part #Description
D2011/4" FNPT
CAUTION: This blow gun does not have a safety by-pass to prevent buildup of tip pressure in the event of tip blockage. It may be used for cleaning purposes only if the air supply (inlet pressure) has been reduced to 30 PSI or less.


Blow Gun Extensions and Tips

Blow Gun ExtensionsSST10 Blow Gun TipD201RT Rubber Tipped Blow Gun Tip
5/16" tip facilitates use in tight places. Blow gun tip thread is 1/8" NPT.SST10 fits all Safety Blow Guns shown except the Push Button Controlled and Full Pressure Blow Guns.D201RT fits Rubber Tipped Blow Guns
Part #Size Extension
BGE66"
BGE1010"
BGE1212"
Part #Description
SST10Standard Tip
D201RTRubber Tipped


Pistol Grip Safety Blow Guns

Pistol Grip Safety Blow Gun
  • Contoured pistol-grip for safe, comfortable handling, even with greasy hands.
  • Convenient "hang-up" hook.
  • Conforms to US Dept. of Labor, OSHA Standard 1910.242 (B) allowing a maximum of 30 PSI outlet pressure at the nozzle when dead-ended.
  • Conforms to US Dept. of Labor, OSHA Standard 1910.95 regulating noise level exposure.
  • Conforms to Title 41, Walsh-Healy Rules and Regulations P50-204.8, Safety and Health Standards.
  • 1/4" Female NPT inlet
Part #Description
PG7001/4" FNPT


Extended Nozzle Pistol Grip Safety Blow Guns

Extended Nozzle Pistol Grip Safety Blow Gun
  • Conforms to US Dept. of Labor, OSHA Standard 1910.242 (B) allowing a maximum of 30 PSI outlet pressure at the nozzle when dead-ended.
  • Conforms to US Dept. of Labor, OSHA Standard 1910.95 regulating noise level exposure.
  • Conforms to Title 41, Walsh-Healy Rules and Regulations P50-204.8, Safety and Health Standards.
  • Slender 4" extended nozzle allows access to hard to reach places and holes as small as .200".
  • Pressure rating - 150 PSI.
  • Variable output trigger enables user to control air flow.
  • Hook design near trigger provides finger protection as well as easy storage.
  • Lightweight to help minimize user fatigue.
  • Side holes allow air to escape if nozzle tip is dead-ended, thus preventing back pressure buildup.
Part #Description
ENBG11/4" FNPT


Hydro-Blast Cleaning Tool & Siphon

SHOULD NOT BE USED WITH MINERAL SPIRITS

Hydro-Blast Cleaning Tool & Siphon
  • Uses siphon to spray solvents or detergent solutions.
  • Uses regular garden hose plus compressed air to blast off dirt and residue.
  • Can be used with hot or cold water. Valve body stays cool even when used with hot water.
  • Used in garages and factories to blast caked-on dirt from vehicles and equipment.
  • Complete, ready to use. D230 includes: Valve body, 2" and 15" extensions, six foot siphon tubing and adapter for garden hose.
Part #Description
D2301/4" FNPT Inlet
The tubing supplied is vinyl and the internal seals in the valve body are Buna-N. Consult chemical resistance charts for compatibility of solvents before putting gun into solvent service. Use safety equipment when using this tool. Eye and skin protection are necessary.


"Coil-Chief" Self-Storing Air Hose

Coil-Chief Self-Storing Air Hose
Part #Male NPT SizeHose ID x Length
CC14121/4"1/4" x 12'
CC14251/4"1/4" x 25'
CC14501/4"1/4" x 50'
CC38253/8"3/8" x 25'
CC38503/8"3/8" x 50'
CC12251/2"1/2" x 25'
CC12501/2"1/2" x 50'
Bulk Hose - No Fittings
CC14100B-1/4" x 100'
CC38100B-3/8" x 100'
CC12100B-1/2" x 100'
Repair / Assembly Kits
PART #Size / Type
RK0901/4" Rigid Male Pipe
RK0921/4" Swivel Male Pipe
RK1103/8" Rigid Male Pipe
RK1123/8" Swivel Male Pipe
RK1181/2" Rigid Male Pipe
RK1191/2" Swivel Male Pipe
"Coil-Chief" comes standard with swivel on one end. Yellow.
Bulk hose needs assembly kits for ends.

Repair / Assembly kits include rigid or swivel male fittings, nut, insert, ferrule and spring guard.

Nylon Working Pressure: 200 PSI at 70ºF


Polyurethane Self-Storing Air Hose

Polyurethane Self-Storing Air Hose
Part #Male NPT SizeHose ID x Length
PU14101/4"1/4" x 10'
PU14151/4"1/4" x 15'
PU14251/4"1/4" x 25'
PU38153/8"3/8" x 15'
PU38203/8"3/8" x 20'
PU38253/8"3/8" x 25'
PU38503/8"3/8" x 50'
PU12151/2"1/2" x 15'
Extremely flexible - resists kinking. Impervious to abrasions, heat and oil. Superior elasticity and coil memory.
Both ends swivel.
Blue.

Polyurethane Working Pressure: 125 PSI at 70ºF


Tire Inflator Gauges

Tire Inflator GaugesTire Inflator Gauges
Heavy duty tire gauge. Has 12" hose with swivel dual foot chuck inflator. Tapered chuck nut fits wheel cover holes on cars and light trucks. Calibrated in 2 PSI increments from 10 to 120 PSI.Tire gauge for passenger cars. Has 12" hose with straight-on chuck. Straight chuck nut fits wheel cover holes on cars and light trucks. Ideal for use on wells and reels. Calibrated in 2 PSI increments from 10 to 90 PSI.
Part #Description
D1011/4" FNPT
Part #Description
D1501/4" FNPT


Dual Foot Gauges

Dual Foot GaugesDual Foot Gauges
Features a heavy duty hang-up ring.
Calibrated in 2 PSI increments from 10 to 130 PSI.		Handy pocket clip.
Calibrated in 2 PSI increments from 20 to 120 PSI.
Part #
DFG2
Part #
DFG1


Tire Inflator Chuck

Ball foot chuck. For direct connection to live air only. Features a built-in shutoff valve (will not work on inflator gauges). Solid brass. 1/4" NPT female thread.
Maximum pressure is 300 PSI.		Tire Inflator Chuck
Part #
D104


Ball and Push-On Ball Swivels

Ball SwivelPush-On Ball Swivel
Brass and hardened steel construction. O-ring seals. "Wobble" action for increased flexibility with air driven tools.These fittings have a special barb design for secure grip in push-on type air hoses.
Part #Hose SizeMale NPT
D444S1/4"1/4"
D446S3/8"1/4"
Part #Hose SizeMale NPT
D444SL1/4"1/4"
D446SL3/8"1/4"


In-Line Swivels

In-Line SwivelIn-Line Swivel
This heavy-duty free turning swivel relieves the hose of twist and torsional strain which always occurs when hose is worked from a rigid outlet. For air service only. Rated to 250 PSI. Steel. Minimum PSI 35.For fast and efficient service that avoids hose kinking. Rated to 150 PSI. for use with air only. Brass.
Part #Male NPTFemale NPT
SV173/8"1/2"
SV201/2"1/2"
SV263/4"3/4"
Part #Male NPTFemale NPT
D344R1/4"1/4"
D366T3/8"3/8"


Steel Bent Stem Swivels

Bent Stem Swivels are designed for normal operation at 90 PSI

Bent Stem Swivel
Part #Description
ATS7812H7/8" - 24 thread x 1/2" hose barb
ATS1212H1/2" NPT thread x 1/2" hose barb
Bent Stem Swivel
Part #Description
ATS7838F7/8" - 24 thread x 3/8" female NPT
Bent Stem Swivel
Part #Description
ATS7838M7/8" - 24 thread x 3/8" male NPT


Air Tool Swivels

Air Tool SwivelSwivels at two locations... so air hose can drop directly to the floor. Rated to 150 PSI. Aluminum.
Part #Size
D344U*1/4"
D346U3/8"
D348U1/2"

* D344U is a non-marring composite and can be used on percussion tools.

To Top

Order Now!